A while back the boss was having a big clear out of this basement, and, having been a fully signed up, Parker-wearing anorak of old, found a GE Superadio 3.
This was made for the US market only, but benefited from a sensitive FM & AM receiver, with an AM "Wide" mode.
In the US, AM channels range from 525KHz to 1705KHz, in 10KHz channels. This gives the station a maximum audio bandwidth of 5KHz, but I suspect many stations may have used more, hence the Superadio being equipped with "Wide" mode for improved audio quality.
In the UK (and EU) , we used 2 AM bands for broadcast , one Longwave (LW or GO in France) and Mediumwave (MW or PO in France). Eventually, after things were standardised throughout Europe, our channels were just 9KHz wide between 525 and 1605KHz (with one other allocation at 1611KHz for Vatican City). This allowed only 4.5KHz of audio, and often a narrower bandwidth of 3.5KHz was used to prevent "splatter" on adjacent channels.
The Superadio is connected up to a variac, and supplied with the required 115V. Nothing. Nada. It's taking no current from the supply. I connect my bench supply, set to 9V to the springs where the 6 D-calls normally reside, and there's a click from the speaker, but nothing more.
Measuring the resistance across the American mains plug shows it's open-circuit. Perhaps the 115V transformer was inadvertently connected to our UK 240V mains, and (rapidly) failed, perhaps damaging the radio circuitry itself before expiring.
Removing the tuning knob, and the bass, treble and volume knobs from the radio, and undoing the 6 screws holding on the back, allow the radio to be removed (not without some struggle) from the case.
The speaker wires are unsoldered, and the workshop speaker temporarily connected.
Getting some life back into the radio is simple, a quick squirt of contact cleaner on the switches and pots restores operation, at least from the bench power supply.
Let's investigate the mains. I'm hoping for a blown fuse, on a transformer which I can simply rewire the primary for 240V operation...
Once the screws to the tuning scale-frame/mechanism and plastic PCB frame are removed, desoldering
the AM radio aerial connector from the rear panel, sufficient access is gained to the underside, where the transformer exists... It must be under that small fibre cover...
The small fibre cover is removed, and all becomes obvious. It's just the strain relief for the mains cable, and a small circuit board for the juction between the transformer primary, and the mains lead (and another mystery component, covered in heatshrink... read on). The transformer is absent without leave. The cover just protected the mains junction, and providing some strain relief for the mains lead. Perhaps the boss removed it to prevent damage if connected up here in the UK?
A small 2 x 6V transformer is ordered, and turns up the next day.
The circuit is very simple. It's just a transformer, and a full-wave rectifier. What bothers me is that mystery component, wrapped in heatshrink. It's connected between one side of the mains, and chassis ground of the radio.
Am I happy about that? I make a post on the VRAT forum for knowledge.
The new transformer is a PCB mounted type, as that's what I could get that would fit. It fits neatly in the hole, and I've superglued it in place, however, it needs some sort of bracket to hold it down.
When I started this repair, I had never used my 3D printer before, so this was first time I've designed something, or 3D printed anything.
A model is created in Fusion 3D. Sliced in Cura, and the results fed into the printer...
And 43 minutes later , it's done!
If you need one, you can pick it up from https://www.thingiverse.com/thing:4859458
So the conjecture on VRAT is that the 2.2M resistor was probably there to assist signal coupling to ground, and is better and safer left out, as I suspected.
I must say I'm very pleased with the results.
The electronics is tested and it's all working well.
... duly painted in a fetching shade of satin black..
The badge is given a dab of hot glue, and it's refitted to the grille.
The knobs are replaced and the radio tested. It sounds great in 'Wide' AM tuned to Absolute on 1215KHz. 
*Further waffle
Then came along "The Pirates" in an attempt to break the BBC's monopoly in the UK. Audio bandwidths were often way wider than the 4.5 KHz permitted, and, certainly channels Like Radio Caroline in the 80's, and the fast-paced Laser 558 produced fabulous (albeit mono) audio. Apparently 9KHz was often the norm, effectively occupying two AM channels. The American Superadio was then a sort-after anorak item for resolving this "extra" bandwidth, despite not being available officially in the UK.
Of course, the last pirate ship fell silent in 1990, but we've got FM (and DAB, I suppose, although quality of DAB can be best described as "variable") now, even if the stations all do sound the same..
Then, after what seemed like an eternity, Radio Caroline managed to get an allocation to permanently transmit on 648KHz. It's got a decent transmitter and aerial (once used by the BBC for the World Service), and can be received further out than it's intended service area of Essex.
Now, as both the boss and myself were interested in it, we set about measuring the bandwidth of Caroline's signal after I commented that it did sound rather "wide". We logged into a few web SDR's to find decent reception, and we measured about 13.8KHz of channel width, corresponding to a very respectable audio bandwidth of 6.9KHz, much outside the required 4.5KHz. Wide indeed. (My boss called people who knew people, who knew people, and ascertained that the audio was indeed 7KHz wide, and the authorities had passed it off, I guess not many people are using AM now, so it's mostly empty, and the problem of adjacent channel splatter has gone away). At the time of writing the BBC is in the process of switching off more medium wave stations up and down the country.
